SMT equipment sourcing · inspection · packing · global delivery

Home / Equipment / Guowei
Overview

Guowei Wave Solder Outfeed Conveyor

Receive boards or carriers at the wave solder exit and deliver them to the next work surface. The pictured Guowei family uses an inclined belt on an open frame. Begin with the actual discharge height, landing height and board contact surfaces before specifying the conveyor.

Model referencesConfiguration checksBuyer's acceptance checksRequest evidence

Guowei Technical Specifications

Key Features

Position in the lineBetween the wave solder outlet and the downstream work surface
ConstructionCatalogue shows an aluminium frame. The supplied photos show an inclined green belt and covered inlet.
Specify for the lineInlet and outlet heights, incline, direction, usable belt width and board or carrier contact surface

Guowei 2024 catalogue, PDF page 23. Manufacturer reference. Confirm the supplied configuration on the quotation.

Typical Applications and Selection

A short, dedicated take-away section makes sense where the process needs to change height before manual inspection or a bench. A powered extension or a supported roller section may suit heavy carriers better. Compare through a transfer trial with the actual hot carrier and a representative board.

Acceptance Trial

Run single boards and closely spaced boards at the planned line speed. Watch the exit lip and both transitions. Agree acceptable contact points, the unloaded restart sequence and a recovery check with the receiving station held.

Machine Images from Different Angles

Match both transfer heights

Measure the discharge at the actual wave solder outlet and the receiving bench with the supports in operating position. Give the supplier both heights, the available floor length and the location of any guards. Ask for a drawing that shows the belt slope and both transfer gaps.

Side view of the inclined frame and inlet cover
Side view of the inclined frame and inlet cover

Check the belt under the real carrier

Use the heaviest carrier and the shortest bare board that will leave the soldering machine. The carrier underside or recently soldered protrusions can determine the belt or roller choice. Ask whether line speed and receiving speed can be matched without the board stopping across the transition.

Inlet-to-outlet sightline over the green belt
Inlet-to-outlet sightline over the green belt

Plan access under the conveyor

The open frame exposes the feet, cable route and drive area. Leave space to clean beneath the belt and reach the motor, and protect cables near the soldering machine. Agree the position of any emergency stop and the handoff behaviour when the downstream station stops.

Opposite side showing the open base and controls
Opposite side showing the open base and controls

Compare the catalogue geometry

The 2024 catalogue shows the wave solder outfeed conveyor family on PDF page 23. Compare the enclosure, operator access and transfer interfaces with the supplied views. For model-specific dimensions, use the applicable configuration table and verify the offered machine.

Guowei catalogue family reference, PDF page 23
Guowei catalogue family reference, PDF page 23

Running Video and Test Evidence

Run single boards and closely spaced boards at the planned line speed. Watch the exit lip and both transitions. Agree acceptable contact points, the unloaded restart sequence and a recovery check with the receiving station held.

Inspection and Export Preparation

Service and Spare Parts

Inspect belt tracking, drive mounting and guards with power isolated. Look for solder debris, loose fasteners and any belt damage from carriers. Obtain the replacement-belt reference and the supplier's cleaning instructions.

Quotation checklist

Include the following when asking for a configuration and acceptance plan.

  • Wave outlet and receiving heights with measured gaps
  • Bare board or solder carrier dimensions and permitted belt contact
  • Solder-process exposure, line speed and downstream stop behaviour

FAQ

Common questions when selecting Guowei Wave Solder Outfeed Conveyor for your line.

01Buying question

What information fixes the slope?

Supply both transfer heights and the horizontal distance available after allowing for guards, service and the downstream station.

02Buying question

Can it also load the wave solder machine?

The catalogue assigns this family to outfeed. For infeed, specify the machine entry, carrier angle, supports and control interface separately.

03Buying question

Is a belt temperature rating published?

The available product description gives no rating. Request the belt specification and confirm exposure using your actual part and process.

Export Packing and Installation

Agree the packed dimensions, handling points and protection for exposed interfaces before arranging freight. Ask for the packing list with loose tools and accessories identified so they can be checked at receiving.

Send Your Guowei Production Requirement

Share the application, dimensions and acceptance requirements. Ask for the fitted configuration, utility drawing and delivery scope.