SMT equipment sourcing · inspection · packing · global delivery

Home / Equipment category / BTU Pyramax 125N
Overview

BTU Pyramax 125N Nitrogen-Capable Reflow Oven

The BTU Pyramax 125N is the air-or-nitrogen model in the 125-inch heated-length class. Choose the atmosphere and transport options against an actual soldering profile.

Official source recordedUnit evidence requiredInspection guideExport support
Manufacturer-published model data

BTU Pyramax 125N Technical Specifications

Heated length3,175 mm in BTU's 125N model table.
ZonesTen heated zones on each side and two cooling zones on each side in the published 125N table.
AtmosphereBTU lists air or nitrogen for the 125N. The 125A column lists air.
Conveyor referenceBTU lists 25–152 cm/min and 51–457 mm for the standard comparison. Check the fitted rails or belt and the qualified process speed.
Cooling lengthThe manufacturer's 125N column lists 1,168 mm, compared with 1,219 mm in the 125A column.
Overall lengthBTU lists 5,844 mm for 125N. Confirm utility and service access using the serial drawing.

Manufacturer model information

Model data describes the published configuration. Confirm fitted options, utilities and condition for the unit offered.

Key Features

Configuration Must Be Verified

Identify the Pyramax 125N data plate and verify nitrogen plumbing, oxygen monitoring, conveyor and cooling options. Establish the available power and site exhaust against the fitted machine rather than the family's broad electrical range.

Buyer decision guide

When BTU Pyramax 125N Makes Sense — and When It May Not

Use board mass, solder paste limits and the oxygen target to plan the comparison. Confirm rail, belt and centre support before assigning the recipe.

Good application fitConsider the 125N where a qualified product profile calls for nitrogen or the same line must run controlled-atmosphere and air jobs. Agree when the oven must switch and what stabilisation evidence is required.
Where to check the limitsIf a heavy board cannot meet the paste and component window at the required board rate, changing the atmosphere alone will not resolve the profile. Compare loaded-board results before adding capacity.

BTU Pyramax 125N Acceptance Plan

Run a thermocouple board through the configured oven. Retain the board profile, recipe, speed and oxygen measurement when nitrogen is specified.

  1. Agree the measurement plan

    Use the paste and component limits that apply to the assembly. Map the thermocouple sites and identify whether an oxygen measurement is part of the acceptance record.

  2. Run with production loading

    Use the agreed spacing and conveyor support. Save the measured board profile, belt speed, setpoints and atmosphere data from the same run.

  3. Check how the oven recovers

    Repeat the board after a planned recipe change or restart. Compare profile shape and discharge temperature with the approved result and record stabilisation time.

Typical Applications

Typical Applications for BTU Pyramax 125N

For a thick multilayer or unevenly populated board, use thermocouples at slow-heating joints and sensitive components. Evaluate the limiting points, not only the average profile.

For frequent changeovers, compare recipe recovery when changing board mass or transport support. Check the output after normal loading resumes, including the cool-down zone.

Before quotation

Three BTU Pyramax 125N Buyer Questions

1

What must the process handle?

Send the drawing, sample or material that defines the hardest job. Review the heated length with that sample in view.

2

Which configuration is on offer?

Require the data plate and a configuration list with included items and separately priced options. Mark the setup used in the trial.

3

How will acceptance be measured?

Agree the result to keep from the trial and how it will be checked after transport. Include unresolved process limits on the order.

Running video confirmation

BTU Pyramax 125N Running Video Review

Show the 125N plate, installed conveyor and oxygen display where fitted. Tie a representative board's entry and exit to the measured profile and recipe record from that run.

Request a dated recording tied to the offered machine's serial and tested sample. The preview opens the evidence request.

BTU Pyramax 125N complete-machine preview for running-evidence requestRequest running video →Actual-unit recording on request
Used-machine inspection

Inspection and Export Preparation for an Actual BTU Pyramax 125N

  • Unit identityMatch the nameplate, electrical label and fitted options to the quotation. Keep any condition notes and missing accessories with that serial.
  • Inspection and maintenanceCheck rail movement and flux-management service condition with the oven isolated per BTU instructions.
  • Acceptance recordRequest the fitted zone and cooling layout, nitrogen and exhaust requirements, conveyor/support options and maintenance history. Confirm residual heat and utilities procedures with qualified site personnel.
  • Export handoffAgree the transport state and the commissioning check. Request dated packing records for the actual unit before dispatch.
Spare Parts

BTU Pyramax 125N Spare Parts Scope

Identify the fitted belts, rails, centre support, cooling and flux-management service items by serial. Confirm the oxygen sensor and its service history if nitrogen performance is part of acceptance.

Quotation checklist

Provide your application, sample details, destination utilities and required delivery scope. Ask the supplier to itemise configuration, service parts, installation and the evidence included with the offer.

Compare nitrogen reflow with a separate curing process

Pyramax 125N is a reflow platform for solder paste profiles. SM-CSUV990 is listed for infrared curing. A process that needs both operations should specify separate material limits, transport constraints and measured board profiles.

SAMTRONIK SM-CSUV990 →

FAQ

Common questions for overseas buyers evaluating a BTU Pyramax 125N.

01Configuration

Can a 125A quote stand in for a 125N?

The heated length matches in the model table. Compare the atmosphere package and cooling configuration separately.

02Selection

Should the nitrogen option set the soldering recipe?

Set the thermal and atmosphere acceptance from the assembly and paste data. Measure both on the actual configuration when nitrogen is required.

03Acceptance

Does the published conveyor speed predict boards per hour?

Use board length, spacing and the speed that meets the measured profile. Include the effect of support, cooling and upstream loading in the line estimate.

Export packing proof

Export Packing and Container Loading

Agree the transport state for rails, cover and removable support equipment. Keep the recipe backup, utility drawing and unpacking instructions with the serial and packing list.

These photos show general export preparation. Request dated protection and loading photos for the specific unit before dispatch.

Crated equipment at a container door
Crated equipment at a container door
Secured cargo inside a container
Secured cargo inside a container
Wrapped machines in a staging area
Wrapped machines in a staging area
Crated equipment at a container door
Crated equipment at a container door
Secured cargo inside a container
Secured cargo inside a container
Wrapped machines in a staging area
Wrapped machines in a staging area

Send Your BTU Pyramax 125N Production Requirement

Share the process, representative job and required evidence. Ask for the fitted configuration and a quotation that distinguishes the machine, tooling, services and delivery.