SMT equipment sourcing · inspection · packing · global delivery

Home / Equipment category / Japan Unix UNIX-DF404S
Overview

Japan Unix UNIX-DF404S Desktop Soldering Robot

The UNIX-DF404S is the wide-work-area desktop soldering robot in Japan Unix's DF line. Decide from the fixture, solder tip access and required joint sequence.

Official source recordedUnit evidence requiredInspection guideExport support
Manufacturer-published model data

Japan Unix UNIX-DF404S Technical Specifications

Work area400 × 365 mm for DF404S.
MotionJapan Unix lists 900 mm/s XY and 400 mm/s Z.
ControllerThe model comparison lists a built-in soldering controller and LAN/COM connectivity.

Manufacturer model information

Model data describes the published configuration. Confirm fitted options, utilities and condition for the unit offered.

Key Features

Configuration Must Be Verified

The DF404S is the desktop soldering robot in Japan Unix's DF series. Identify the fitted soldering head, wire feeder, tip and controller and confirm any extra-axis option. Treat published motion range as a screening figure.

Buyer decision guide

When Japan Unix UNIX-DF404S Makes Sense — and When It May Not

Check tip approach against tall parts and fixture clamps. Compare any extra-axis requirements with the options actually included.

Good application fitUse point soldering where the tip can reach individual joints in a repeatable fixture. Include a high thermal mass joint and a tight-clearance joint in the review.
Where to check the limitsIf access is restricted by tall parts or the process needs another heating method, compare the actual tool approach and board thermal limits. A larger work area alone cannot resolve a blocked joint.

Japan Unix UNIX-DF404S Acceptance Plan

Run the buyer's board and wire solder. Review joint appearance, wetting and tip access at the highest thermal load and tightest clearance.

  1. Check tip access and fixture

    Use a dry run with the fitted tip and wire guide. Verify clearance at the closest component and show the board support at the joint.

  2. Inspect the trial joints

    Apply the specified material and approved profile. Examine the highest thermal load and tightest joints using the buyer's acceptance criteria.

  3. Test the first joint after changeover

    Change or reload the fixture under the intended procedure. Confirm positioning and repeat the inspection with the programme and tool identity recorded.

Typical Applications

Typical Applications for Japan Unix UNIX-DF404S

Evaluate a connector or other assembly with accessible joints and a controlled board support. Bring the real part and solder material so the setup can be tested at representative thermal loads.

For short runs with changing products, check fixture exchanges, tip changes and programme selection. Record which tooling must travel with each assembly type.

Before quotation

Three Japan Unix UNIX-DF404S Buyer Questions

1

What must the process handle?

Send the drawing, sample or material that defines the hardest job. Review the work area with that sample in view.

2

Which configuration is on offer?

Require the data plate and a configuration list with included items and separately priced options. Mark the setup used in the trial.

3

How will acceptance be measured?

Agree the result to keep from the trial and how it will be checked after transport. Include unresolved process limits on the order.

Running video confirmation

Japan Unix UNIX-DF404S Running Video Review

Show the fitted tip and wire feed, then follow a complete joint on the buyer's sample. Include the close-up and its inspection record, especially at a restricted access point.

Request a dated recording tied to the offered machine's serial and tested sample. The preview opens the evidence request.

Japan Unix UNIX-DF404S complete-machine preview for running-evidence requestRequest running video →Actual-unit recording on request
Used-machine inspection

Inspection and Export Preparation for an Actual Japan Unix UNIX-DF404S

  • Unit identityMatch the nameplate, electrical label and fitted options to the quotation. Keep any condition notes and missing accessories with that serial.
  • Inspection and maintenanceUse the prescribed tip care method and check wire feed alignment. Reconfirm the tool position after service.
  • Acceptance recordRetain the exact tip, wire feeder and controller, fixture and programme revision. Confirm site extraction and any fitted interfaces for data or line integration.
  • Export handoffAgree the transport state and the commissioning check. Request dated packing records for the actual unit before dispatch.
Spare Parts

Japan Unix UNIX-DF404S Spare Parts Scope

Identify approved tip codes, wire guides, heaters, fixtures and controller-related items for the proposed unit. Separate consumables from setup tooling and calibration services.

Quotation checklist

Provide your application, sample details, destination utilities and required delivery scope. Ask the supplier to itemise configuration, service parts, installation and the evidence included with the offer.

Plan soldering and extraction as separate acceptance checks

Compare the soldering trial on DF404S and the hood capture measurement with a proposed extractor. Position extraction so it does not interfere with tool access and verify it under the site's approved procedure.

SAMTRONIK SM-DH1100 →

FAQ

Common questions for overseas buyers evaluating a Japan Unix UNIX-DF404S.

01Configuration

Does the DF404S label establish a laser configuration?

Japan Unix lists separate laser models. Identify the actual tool, controller and approved configuration.

02Selection

Can top speed determine completed joints per hour?

Measure approach, heating, solder feed, dwell and inspection on the actual joint list. Add board handling and any tip service in the shift estimate.

03Acceptance

When should the tool reference be checked?

Check after tip, mount or fixture changes and before qualifying the first board. Keep the approved joint result with the setup reference.

Export packing proof

Export Packing and Container Loading

Protect the soldering head and label the loose feeders and fixtures. Retain the fitted tool reference and first-joint inspection to repeat the setup after transport.

These photos show general export preparation. Request dated protection and loading photos for the specific unit before dispatch.

Crated equipment at a container door
Crated equipment at a container door
Secured cargo inside a container
Secured cargo inside a container
Wrapped machines in a staging area
Wrapped machines in a staging area
Crated equipment at a container door
Crated equipment at a container door
Secured cargo inside a container
Secured cargo inside a container
Wrapped machines in a staging area
Wrapped machines in a staging area

Send Your Japan Unix UNIX-DF404S Production Requirement

Share the process, representative job and required evidence. Ask for the fitted configuration and a quotation that distinguishes the machine, tooling, services and delivery.