SMT equipment sourcing · inspection · packing · global delivery

Home / Equipment category / Southern Machinery SME-6300
Overview

Southern Machinery SME-6300 Inline PCBA Cleaning Machine

The SME-6300 combines chemical wash, DI rinse and hot-air drying in an inline machine. Size the utility and drain arrangements with the board flow.

Official source recordedUnit evidence requiredInspection guideExport support
Manufacturer-published model data

Southern Machinery SME-6300 Technical Specifications

Board envelopeSouthern Machinery lists 50 × 50 to 500 × 400 mm, up to 100 mm loaded thickness.
Transport500 mm conveyor net. Published left-to-right speed range is 0.1–1.5 m/min.
Installed utilitiesThe model table lists 380 V three-phase power and 6–15 L/min DI water.
Conveyor heightSouthern Machinery lists 900 ±25 mm for the net conveyor.
Wash and drying limitsThe model table gives maxima of 80 °C for wash, 60 °C for DI rinse and 100 °C for hot-air drying. Process settings depend on material and the qualified recipe.
Air supplyThe model table lists 0.5–0.7 MPa and 200–400 L/min. Confirm the supplied configuration and utility connection.
Installation referenceThe supplier lists 5,200 × 1,650 × 1,650 mm and 2,800 kg. Allow separate space for utility and service access.

Manufacturer model information

Model data describes the published configuration. Confirm fitted options, utilities and condition for the unit offered.

Key Features

Configuration Must Be Verified

Confirm the SME-6300 conveyor, actual utilities and sequence on the data plate and serial documents. Plan DI supply, drain handling, power, exhaust and access for maintenance against the fitted machine.

Buyer decision guide

When Southern Machinery SME-6300 Makes Sense — and When It May Not

Evaluate the minimum clearance under the transport and confirm that the PCB stays supported at the required rate.

Good application fitAn inline cleaner is a candidate when the upstream and downstream flow can use the same orientation and line rate. Establish the clean and dry conditions needed at the next station.
Where to check the limitsA change in board speed affects exposure through the wash, rinse and dry zones. If the required condition is not met at the intended rate, investigate chemistry, loading and the line balance before increasing output.

Southern Machinery SME-6300 Acceptance Plan

Run the worst-case board through wash, rinse and dry. Record carry-over, visible residue and moisture at the exit.

  1. Confirm utilities at load

    Measure the available DI supply and confirm drain routing with the site team. Verify air and power requirements from the serial documents before planning a live run.

  2. Watch the worst-case board through the line

    Record the conveyor speed, panel orientation and approved process settings. Check the board at exit for the agreed residue and moisture indicators.

  3. Test a restart or change of format

    Repeat the witness assembly after the normal transition. Watch for transfer interruptions and record which conveyor, chemistry or rinse conditions changed.

Typical Applications

Typical Applications for Southern Machinery SME-6300

Run an assembly with shields, connector pockets and height close to the proposed handling limit. Check that supports stay clear of areas where the process must reach.

When the next step is coating or packing, agree how boards are handled after drying. Preserve the witness sample and identify any waiting or transfer state where contamination can return.

Before quotation

Three Southern Machinery SME-6300 Buyer Questions

1

What must the process handle?

Send the drawing, sample or material that defines the hardest job. Review the board envelope with that sample in view.

2

Which configuration is on offer?

Require the data plate and a configuration list with included items and separately priced options. Mark the setup used in the trial.

3

How will acceptance be measured?

Agree the result to keep from the trial and how it will be checked after transport. Include unresolved process limits on the order.

Running video confirmation

Southern Machinery SME-6300 Running Video Review

Follow the actual conveyor loading and recipe indication through discharge. Show the same sample at exit and the recorded rinse or dry observations, without substituting a different board.

Request a dated recording tied to the offered machine's serial and tested sample. The preview opens the evidence request.

Southern Machinery SME-6300 complete-machine preview for running-evidence requestRequest running video →Actual-unit recording on request
Used-machine inspection

Inspection and Export Preparation for an Actual Southern Machinery SME-6300

  • Unit identityMatch the nameplate, electrical label and fitted options to the quotation. Keep any condition notes and missing accessories with that serial.
  • Inspection and maintenanceCompare nozzle condition and rinse measurements before and after service. Check filter and tank cleaning procedures against the material used.
  • Acceptance recordRetain the serial, net conveyor height and direction, utility drawing, drain layout and maintenance record for filters and tanks. Confirm any receiving-site restrictions before arranging freight.
  • Export handoffAgree the transport state and the commissioning check. Request dated packing records for the actual unit before dispatch.
Spare Parts

Southern Machinery SME-6300 Spare Parts Scope

Identify spray nozzles, conveyor net and guides, filters and pump/seal service items. Obtain the fitted codes and check fluid compatibility before accepting a replacement.

Quotation checklist

Provide your application, sample details, destination utilities and required delivery scope. Ask the supplier to itemise configuration, service parts, installation and the evidence included with the offer.

Compare with batch spray-in-air cleaning

A batch cleaner allows boards to be arranged in frames. The inline SME-6300 ties exposure to conveyor travel. Use the same witness board to compare quality and real shift output, including manual handling.

PBT Works HyperSWASH III →

FAQ

Common questions for overseas buyers evaluating a Southern Machinery SME-6300.

01Configuration

Can tank settings be copied to a different line?

Agree the recipe with the chemistry supplier and validate it with the intended board, conveyor speed and loading.

02Selection

Can a catalogue temperature maximum be used as the recipe?

Use the qualified chemistry and assembly limits and verify the measured result. Catalogue limits describe the equipment envelope.

03Acceptance

What if a board transfers correctly but exits wet?

Record the orientation, load and speed. Inspect retention areas and separate the drying check from the wash and rinse results before adjusting the process.

Export packing proof

Export Packing and Container Loading

Confirm the drained and documented transport state with the equipment supplier. Mark the utility connections, retain any removed guards and include the verified unloading and commissioning plan.

These photos show general export preparation. Request dated protection and loading photos for the specific unit before dispatch.

Crated equipment at a container door
Crated equipment at a container door
Secured cargo inside a container
Secured cargo inside a container
Wrapped machines in a staging area
Wrapped machines in a staging area
Crated equipment at a container door
Crated equipment at a container door
Secured cargo inside a container
Secured cargo inside a container
Wrapped machines in a staging area
Wrapped machines in a staging area

Send Your Southern Machinery SME-6300 Production Requirement

Share the process, representative job and required evidence. Ask for the fitted configuration and a quotation that distinguishes the machine, tooling, services and delivery.