SMT equipment sourcing · inspection · packing · global delivery

Home / Equipment category / Mycronic MYD50
Overview

Mycronic MYD50 Inline Dispensing System

The Mycronic MYD50 supports inline dispensing with configurable conveyor stations. Pick the handling and heating configuration before comparing the nominal dispense motion.

Official source recordedUnit evidence requiredInspection guideExport support
Manufacturer-published model data

Mycronic MYD50 Technical Specifications

Material handlingMycronic describes edge clamps, vacuum blocks and heating modules as conveyor configuration options.
Tool accessThe manufacturer lists pneumatic and electrical tilt and rotation options.

Manufacturer model information

Model data describes the published configuration. Confirm fitted options, utilities and condition for the unit offered.

Key Features

Configuration Must Be Verified

MYD50 conveyor stations and dispense tools can be configured. Request the installed valve, board supports, clamps, sensors and any heater or tilt/rotation option. Confirm the material delivery system separately from the platform.

Buyer decision guide

When Mycronic MYD50 Makes Sense — and When It May Not

Map clamps and keep-out areas against every dispense path. Choose the valve and board support with the actual material and carrier.

Good application fitIt is a candidate for repeated inline dispensing where the board can enter, locate and exit without manual fixture changes. Establish clamp repeatability with the real pallet before selecting a deposition programme.
Where to check the limitsFor edge deposits or tall assemblies, verify fixture access and the sweep of the actual head and hoses. A machine with adequate axis reach can still have an unusable path after clamping.

Mycronic MYD50 Acceptance Plan

Run a panel from transfer through dispense and discharge. Compare material deposition near the edges and after an idle restart.

  1. Map the loaded board

    Locate fiducials, clamps, supports and keep-outs on a board drawing. Mark the narrowest usable path with the valve at the intended approach angle.

  2. Compare first and steady deposits

    Measure agreed features from the first board and after a normal restart. Record pressure, temperature or other process inputs only where they apply to the fitted valve and material.

  3. Track the conveyor handoff

    Watch transfer and clamping through a repeat load. Compare the deposit at the panel edges and note any upstream waits, positioning retries or manual interventions.

Typical Applications

Typical Applications for Mycronic MYD50

Assess adhesive dots or fluid paths where line transfer and board location determine the final deposit. Include boards with different surface heights or near-edge features in the sample set.

If heating or a multi-station arrangement is proposed, record the material state at dispense. Check whether the transition between stations changes open time or board location.

Before quotation

Three Mycronic MYD50 Buyer Questions

1

What must the process handle?

Send the drawing, sample or material that defines the hardest job. Review the material handling with that sample in view.

2

Which configuration is on offer?

Require the data plate and a configuration list with included items and separately priced options. Mark the setup used in the trial.

3

How will acceptance be measured?

Agree the result to keep from the trial and how it will be checked after transport. Include unresolved process limits on the order.

Running video confirmation

Mycronic MYD50 Running Video Review

Show one panel entering and clamping, then the fitted valve dispensing at a restricted edge. Include the output board and the deposit measurement from that panel.

Request a dated recording tied to the offered machine's serial and tested sample. The preview opens the evidence request.

Mycronic MYD50 complete-machine preview for running-evidence requestRequest running video →Actual-unit recording on request
Used-machine inspection

Inspection and Export Preparation for an Actual Mycronic MYD50

  • Unit identityMatch the nameplate, electrical label and fitted options to the quotation. Keep any condition notes and missing accessories with that serial.
  • Inspection and maintenanceVerify valve service condition, reference calibration and conveyor support whenever the dispense setup changes.
  • Acceptance recordDocument the installed conveyor stations, location references, valve and calibration tooling. Request the maintenance history for the material circuit and identify any option needed to repeat the trial.
  • Export handoffAgree the transport state and the commissioning check. Request dated packing records for the actual unit before dispatch.
Spare Parts

Mycronic MYD50 Spare Parts Scope

Quote valve-specific seals, nozzles and feed components separately from rails, clamps and board supports. Establish which parts are material-specific and obtain the fitted tool code before ordering.

Quotation checklist

Provide your application, sample details, destination utilities and required delivery scope. Ask the supplier to itemise configuration, service parts, installation and the evidence included with the offer.

Compare inline with tabletop dispensing

MYT50 is a bench platform whose repeatability depends on fixture loading. MYD50 adds conveyor transfer and station configuration. Compare deposit quality on the same part, then account for how often boards are loaded, moved or re-fixtured.

Mycronic MYT50 →

FAQ

Common questions for overseas buyers evaluating a Mycronic MYD50.

01Configuration

Are all handling modules included?

The conveyor modules are configurable. Request an itemized unit configuration and a run using your board.

02Selection

Should the conveyor option be selected after the valve?

Check both together. Clamps, support, height and material delivery can change whether the chosen valve reaches the required area.

03Acceptance

How should a restart be approved?

Compare first deposits with stable results after a normal idle interval. Save the programme and process inputs so the trial can be reproduced after installation.

Export packing proof

Export Packing and Container Loading

Use the approved material isolation and transport procedure. Label any removed valves, stations and cables by their installed location and record the alignment check needed at commissioning.

These photos show general export preparation. Request dated protection and loading photos for the specific unit before dispatch.

Crated equipment at a container door
Crated equipment at a container door
Secured cargo inside a container
Secured cargo inside a container
Wrapped machines in a staging area
Wrapped machines in a staging area
Crated equipment at a container door
Crated equipment at a container door
Secured cargo inside a container
Secured cargo inside a container
Wrapped machines in a staging area
Wrapped machines in a staging area

Send Your Mycronic MYD50 Production Requirement

Share the process, representative job and required evidence. Ask for the fitted configuration and a quotation that distinguishes the machine, tooling, services and delivery.