SMT equipment sourcing · inspection · packing · global delivery

Home / Equipment category / QUICK ET8484
Overview

QUICK ET8484 Four-Axis Tabletop Dispenser

The ET8484 adds a rotary axis to a tabletop XYZ dispensing platform. The extra axis is useful when a path must stay oriented to the part.

Official source recordedUnit evidence requiredInspection guideExport support
Manufacturer-published model data

QUICK ET8484 Technical Specifications

Travel400 × 400 × 100 mm in XYZ. QUICK lists ±180° rotation.
Repeat positioningQUICK lists ±0.01 mm for XYZ motion.
Published load8 kg on the platform and 3 kg for the ZR head.
Axis speedQUICK lists 0.1–600 mm/s in XY and 0.1–300 mm/s in Z.
Cabinet sizeThe table gives 690 × 765 × 836 mm and 49 kg. Include the fitted accessory envelope when planning a bench.

Manufacturer model information

Model data describes the published configuration. Confirm fitted options, utilities and condition for the unit offered.

Key Features

Configuration Must Be Verified

The ET8484 reference includes a fourth rotary axis. Quote the installed holder, rotary tooling, valve and controller together. The rated platform and ZR loads cover different parts of the assembly.

Buyer decision guide

When QUICK ET8484 Makes Sense — and When It May Not

Check the rotary sweep with the complete fixture and valve hoses in place. Nominal travel is measured separately from the collision-free working envelope.

Good application fitUse rotary motion where the tool or part must change orientation around a joint while retaining access. Draw the full sweep of the valve and cable path on the actual fixture before selecting it.
Where to check the limitsFor a flat board reached with XYZ moves alone, a rotary axis can add setup without removing the real process bottleneck. Compare head load, fixture clearance and fluid timing with the simpler route.

QUICK ET8484 Acceptance Plan

Run a dry path at the tightest corners, then dispense on actual parts. Verify the bead at rotation reversals and restarts.

  1. Draw the sweep before dispensing

    Use a dry cycle with the heaviest fixture and the proposed valve. Check clearance at rotation limits and record any path regions excluded by the holder or hoses.

  2. Measure the difficult bead locations

    Compare the bead width, position or continuity where rotation starts, reverses and stops. Use the same material state throughout the comparison.

  3. Repeat the tool reference

    Remove and replace the fixture under the intended change procedure. Recheck rotary zero and tool centre, then compare the deposit at the critical locations.

Typical Applications

Typical Applications for QUICK ET8484

A curved or wrapped seal path is a useful trial when its application angle matters. Mark the points where rotation reverses and where the valve must begin and end output.

For a small batch with several fixture variants, teach a real changeover and check whether a shared tool centre or a new reference is required for each holder.

Before quotation

Three QUICK ET8484 Buyer Questions

1

What must the process handle?

Send the drawing, sample or material that defines the hardest job. Review the travel with that sample in view.

2

Which configuration is on offer?

Require the data plate and a configuration list with included items and separately priced options. Mark the setup used in the trial.

3

How will acceptance be measured?

Agree the result to keep from the trial and how it will be checked after transport. Include unresolved process limits on the order.

Running video confirmation

QUICK ET8484 Running Video Review

Show the actual fixture through the full rotary sweep and follow the nozzle at a reversal. Include a measured bead or sample close-up and the tool identification.

Request a dated recording tied to the offered machine's serial and tested sample. The preview opens the evidence request.

QUICK ET8484 complete-machine preview for running-evidence requestRequest running video →Actual-unit recording on request
Used-machine inspection

Inspection and Export Preparation for an Actual QUICK ET8484

  • Unit identityMatch the nameplate, electrical label and fitted options to the quotation. Keep any condition notes and missing accessories with that serial.
  • Inspection and maintenanceAfter changing the holder, recheck rotary zero and tool-centre offset before running the stored path.
  • Acceptance recordRequest the rotary attachment ID, tool-centre calibration reference, fixture weight and part clearance. Preserve the teach file and show that the quoted controller can load it.
  • Export handoffAgree the transport state and the commissioning check. Request dated packing records for the actual unit before dispatch.
Spare Parts

QUICK ET8484 Spare Parts Scope

Identify the rotary assembly, tool holders, motion and material service items and approved valve consumables. Use fitted model or drawing references for each line in the parts quote.

Quotation checklist

Provide your application, sample details, destination utilities and required delivery scope. Ask the supplier to itemise configuration, service parts, installation and the evidence included with the offer.

Compare four-axis and three-axis QUICK platforms

ET8484 adds rotation and has a different published Z-head load from ET8J493SF. Use the path geometry to decide if rotation is needed, then confirm the actual fixture, valve and clearance.

QUICK ET8J493SF →

FAQ

Common questions for overseas buyers evaluating a QUICK ET8484.

01Configuration

Does motion repeatability define bead tolerance?

Measure bead placement and material output separately under the agreed process settings.

02Selection

Does ±180 degrees describe a usable sweep with every tool?

It is a published axis range. A fitted tool, hose or fixture can reduce safe clearance. Observe the complete dry path before evaluating the wet bead.

03Acceptance

Which load includes the dispense valve?

List the valve, mount and material lines carried by the moving head and compare that mass with the applicable ZR rating. Check the platform load separately.

Export packing proof

Export Packing and Container Loading

Agree how the rotary fixture and valve are immobilised or packed separately. Label teaching references and confirm the axis zero and tool offset after unpacking.

These photos show general export preparation. Request dated protection and loading photos for the specific unit before dispatch.

Crated equipment at a container door
Crated equipment at a container door
Secured cargo inside a container
Secured cargo inside a container
Wrapped machines in a staging area
Wrapped machines in a staging area
Crated equipment at a container door
Crated equipment at a container door
Secured cargo inside a container
Secured cargo inside a container
Wrapped machines in a staging area
Wrapped machines in a staging area

Send Your QUICK ET8484 Production Requirement

Share the process, representative job and required evidence. Ask for the fitted configuration and a quotation that distinguishes the machine, tooling, services and delivery.